gnugk [-hdrt] [-c filename] [-s section] [-l n] [-b n] [-u name] [-d name] [-rr] [-o filename] [–pid filename] [–core A detailed explanation can be found in the manual. /etc/default/gnugk /etc/ /etc/init.d/gnugk /usr/sbin/addpasswd /usr/ sbin/gnugk /usr/share/doc-base/gnugk-manual /usr/share/doc/gnugk/changelog. Open Phone Abstraction Library (OPAL) is a C++ multi-platform, multi-protocol OpenH This project has been superseded by OpalVoip Rocket.
|Published (Last):||23 January 2013|
|PDF File Size:||14.24 Mb|
|ePub File Size:||12.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
SQL has been configured, apply assignments to gateway registrations default. If disabled, the first available gateway will be selected. Forcefully unregister an endpoint by it’s endpoint ID.
Please join the mailing list before posting. This section configures GnuGk to read the assigned aliases from a database. This section configures GnuGk to read the assigned Languages from a database. This command is used as a response to a RouteRequest event see below. Show all people on the status port. These parameters are defined: In the following example, the gateway “test-gw” will be responsible for prefixes “02” and “03” with a priority of 3, and for “04” with a priority of 1.
The network specifies the IP where the RAS message is received from, the setting specifies whether to use the rasAddress. GWPrefixes] This section configures how dialed E. This switch is designed when set to 0 to use additiveRegistrations with gateways so that the assignedAliases are not all assigned upon registration but only when the additiveRegistration is made.
Forcefully unregister an endpoint by IP and call signaling port. Ongoing calls remain active, endpoints that are in a call remain registered. Entering gnuhk or h will display a list of all manua commands. The alias parameter is required, but if you use a dash “-” as alias name, no alias will be set in the destination, just the IP.
This switch removes during registration any TerminalAliases that have not been Authenticated. Endpoints in all other networks will use the globally defined alternate gatekeeper.
For security reasons, the default is not to allow any access until you have configured GkStatus:: A manual for your version is in your GnuGk download archive. Example to hide Tandberg’s neighbor check and traversal zone keepalive messages: If a gateway has registered with the specified alias, all numbers beginning with the prefixes are routed to that gateway. Terminate this call on a virtual queue. However, if the detection fails, you can specify it manually in this section.
The interface is a simple TCP port default: If you do so, the callID parameter must be present. PrintNeighbors Print a list of all neighbor gatekeepers with IP numbers and state. A PDF version can be found in the download section.
Trace Set the status interface output trace level. Route gnug call on a virtual queue to the specified alias. Level 0 Reload notifications and direct replies to gngk commands. Disconnect all calls of a registered ghugk by one of its endpoint identifier. When the gatekeeper does not receive a keep-alive RRQ from an endpoint within the TimeToLive time period, it sends an IRQ message to “poll” the manuzl and check if it msnual alive. Findf Find a registered endpoint by an alias or a prefix.
If an endpoint has more than one active call, the packet loss and jitter values are from one randomly selected call. This allows the assigning of aliases to endpoints as they register, allowing them to set their fully qualified E.
The GNU Gatekeeper Manual
Route this call on a virtual queue to the specified alias and set the destinationSignalAddress. You’ll have to modify it a little to fit your needs. Status port filtering facilitates control of the amount and type of output messages shown to the end user.
Statisticss Show the statistics information of the gatekeeper. Filtering control is performed using the following set of commands: It also also contains patented H. Port MessageType; Request for an external application to gnhgk an incoming call on a virtual queue. This may happen when an endpoint is using a PPP connection e.
Downloading File /PDF Manual (English)//gnugk-manualpdf – GNU Gatekeeper (GnuGk) – OSDN
The default is not to use it. Request for an external application gnufk route an incoming call on a virtual queue. This manal allows GnuGk to read the assigned gatekeepers from a database. Gateway entries may also optionally include vendor information which is stored with the gateway record Format: You can optionally also set the numeric H. This allows you to integrate basic functionality into the gatekeeper and provide source for mabual but keep other parts of your application private.
MakeCall] for configuration options. If the prefix priority and overlaps the GatewayPriority see section [EP This section allows you to define when GnuGk should use the rasAddress inside the message it has received instead of the address where it has received the message from.
Valid endpoint types are: Send trace output to another file. Yell [message text] Example: