4. nov Users Manual Generator ECI FUEL SYSTEMS than 15 ethanol blend or biodiesel blends in excess of B USER MANUAL BG 20 ECI MUX. BG 20 ECI Home · BG 20 ECI Eci TelecomBg Bg and Bg overview of eci adm APC ECM-ECI Error Codes Ver Codigos de Error. BGB/E. Miniature Optical Service Access Platform. Targeting a range of ECI Telecom Transport Networking Division’s BroadGate BGB (Basic unit) fulfills.
|Published (Last):||23 May 2014|
|PDF File Size:||5.81 Mb|
|ePub File Size:||19.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
ECI BG 20/30 MUX – (2-Days) – Cognitel
Click Apply to send cei port STP settings to the equipment and the database. The BG Orderwire Configuration window opens. This address is valid for the gateway mode and Ethernet-only mode. Set the port priority parameters, as follows: If the logical configuration is inconsistent with the physical configuration, alarms such as card out, card unexpected, card type mismatch, and card fault CBUS disconnection will occur.
ECI BG 20/30 MUX – (2-Days)
Port Attributes window for LAN ports If the priorities are the same, the bridge with the lowest node ID is the root bridge. Click OK to delete the trail. Maintenance List window 2. After you set the refresh interval and click Start Refresh, current performance data is retrieved based on the specified monitoring cycle interval minute or hour.
For the alarm generation hold-off period, an alarm event is not reported and the current alarm status not updated until a generated alarm is detected and its alarm status lasts three to 30 seconds. Information contained in the documentation and in the disk is periodically updated, and changes will be incorporated in subsequent editions.
BG slot assignments are shown in the following figure. STP defines a tree with a root bridge and a loop-free path from the root to all network devices in the Layer 2 network. An event indicates that the equipment generated a certain action or process under some condition, but that the action or process itself does not influence the traffic.
The following terms are relevant for NE alarm log queries: Confirmation message when deleting a server trail Specify the filtering conditions you want by selecting the corresponding checkbox es. Select the Alarm Attributes Table tab. By examining the hour performance for a yearThe or several years, you can analyze the long-term running of the equipment.
You do not need to configure port attributes manually. This attribute must eic set on the following cards: Otherwise, a packet is normally classified as Low priority unless at least one of the following is true: The bridge with the highest priority is the root bridge.
Modify object parameters as required.
Orderwire Configuration window – Setting the Orderwire Attribute tab Trace MAC window 2. Enter a numeric value between 1 to for the policer. These conditions result in an unstable network. Orderwire Configuration window – Setting Orderwire Routing tab NE management attributes refer to information used for management purposes, such as the vendor, location, user label, run date, and notes. After slots are assigned on one of these cards, you set the card’s maximum traffic.
Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.
If a port has autonegotiation enabled, the port’s attribute range Duplex, Speed, Flow Control in the port attributes table contains the optimized values in the autonegotiation range.
The traffic here refers to the average traffic within the first 15 minutes in the acquisition process.
You can filter by alarm object, alarm severity, alarm type, and acknowledge status. These attributes are for identification purposes only.
To correct an alarm on a card: To view detailed information for an historical alarm: However, you must click Apply for the attribute configuration on a card to take effect. For the BG NE: To reset performance counters: The Boot Configuration Tool logs in the Ecl automatically and the following Information window appears, confirming automatic login.
You can display all historical alarms, all alarms eck a selected NE, alarms for a selected card, or alarms for a selected functional block.
In the NE tree, select the card that needs a loopback and click Query to query the LCT-BGF database the about the loopback status of the timeslots belonging to this card. Return Command window displaying the run time Set the Protocol Mode by selecting the relevant Unidirectional or Bidirectional radio button.
The main features of FEoS ports are: The parameters in these tabs set Layer 2 and port parameters, respectively.
BG 20 ECI MUX.pdf
Select the Instance tab. The Download Embedded Software window opens. A confirmation message is displayed in the Operation Result area of the window. Serial Port Configuration window The hold-off time is defined by the alarm generation hold-off period and the alarm clearance hold-off period.