Honda VLX Deluxe – bought/sold – project bike Yamaha R1 – fast as Posts: You can get a free manual from too. Here is a link to the Classic: Kawasaki Vulcan Classic Motorcycle Owners Manual – Kawasaki Vulcan Classic LT USB Factory Service Shop Manual. [EBOOK] Kawasaki Vulcan Classic Owners Manual PDF Books this KMG Kawasaki Vulcan Classic YTXBS.
|Published (Last):||9 November 2015|
|PDF File Size:||20.45 Mb|
|ePub File Size:||7.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the wheel stops of its own accord in various positions, it is well balanced. Be sure to maintain proper alignment and use smooth movements when installing. This claxsic includes the latest information available at the time of printing. Through the brake hose. Do not use any other battery except for a 12 V sealed battery as a power source. Valve oil seal damaged Replace see chapter 5. Right Switch Housing Harness Connector 2.
Vulcan 900 Manual
Subthrottle Valve Actuator 7. Sulfation occurs when the battery is charged using an appropriate charger left in a discharged ownwrs for an ex- check with your Kawasaki dealer. The radiator fan may start even if the owjers switch is off. Fuel Pump Relay D: Oil Pressure Switch Lead oeners. Vulcan Fast Shipping, Easy Returns. This will burn out the diodes on the electrical parts. Clamp the rear fender harness with the reinforce attached clamps.
Sulfate is a normal by If you will not be using the motorcy- product of the chemical reactions within cle for longer than two weeks, the maanual battery. Measure the clearance when engine is cold. Con- sult your authorized Kawasaki dealer or local environmental waste agency for their proper disposal procedure. Water Temperature Sensor Roll the taillight lead to the pin. Vacuum Hose California Model 8. Engine Oil Flow Chart Now only if there was a repair manual like that.
Purge Hose Green These serial numbers may be needed by your dealer when ordering parts. Throttle valves or actuator trouble Inspect see vu,can 3. Close the throttle while pulling in the clutch lever. Apply molybdenum disulfide grease. Subthrottle Valve Actuator Drive Signal 1 The headlight comes on after the starter button is released and stays on until the ignition switch is turned off.
To view links or images in signatures your post count must be 1 or greater.
Vulcan Manual | eBay
Oxygen Sensor 1 3. Type Telescopic fork Wheel Travel mm 5.
Do not apply rub- ber protectant to any tread area. The initial maintenance is vitally important and must not be neglected.
If not, the steering stem bearings may be damaged. Brakes 1 mm 0. See the Storage section in this manual.
Gaskets, O-rings, oil seals, grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled. If the reading of input voltage is less than the standard, check the ECU for its ground, power supply maanual wiring shorted. Such a shock to the ECU can damage it. Bolt And Nut Tightening Kawasakj accordance with the Periodic Maintenance Chart, it is very important to check the tightness of the bolts and nuts listed here.
Remove the oxy- gen sensor see Switch and Sensors section in the Electri- cal System chapter. Run the breather hose to the inside of the engine bracket and frame cross pipe front. Alternator Cover Installation, Stator Coil Removal, Stator Coil Installation Apply silicone sealant to the circumference of the alterna- tor lead and crankshaft sensor lead grommets, and fit the grommets into the notch of the cover securely. This is a gently used owners manual for Kawasaki Classic Vulcan models.
Loading Information Kawasaki Parts Accessories, Kawasaki has no control over the Because a motorcycle is sensitive to design or application of accessories. Clutch Spring Free Length VND clsssic mm Run the clutch cable through the brake hose front side.
Kawasaki Vulcan Classic – Owner’s Manual – Pages – PDF
If any one of them shows visible damage, replace the cap with a new claasic. Pump the brake lever until it becomes hard, and apply the brake lever and hold it [A].
Stopping the Motorcycle in an 2. I was looking for one of those, thank you. Install the shim specified where the lines intersect.